Tag: Bosch

Vaillant Boiler Repairs London
Boiler Repair, Vaillant

Vaillant Boiler Repair London

Expert Vaillant Boiler Repair London

Having a damaged Vaillantbroker automatically means no more hot water or heating in your home. How do you expect to cope with that? Of course, you can’t! Are you going through such in your home? If yes, then what you need right now is a Vaillant repair.

Looking for where to get the best? We have that just right here. Valliant Boiler Repair London offers the best of Vaillant repairs all across the magnificent city of London. With many years of experience taking care of gas and water heating system, we count ourself as one of the fore frontiers in the business.

Over the years, we have been able to groom specialists who are experienced, flexible and knowledgeable in Vaillant repairs. This makes us the best option you have if you truly want to make your Vaillant boiler function optimally and remain at their best for a long period.

Vaillant Repairs London

Safety is of paramount importance in our Vaillant repairs. Which is why we adhere strictly to health and safety regulations without any form of filter. This habit has earned several accreditations from recognized bodies such as the National Inspection Council for Electrical Installation Contractors and Gas Safe,  the Institute of Plumbing and Heating Engineers, and many more. With this in place, you should be assured that you are getting nothing but the best from us.

Why Choose Vaillant Boiler Repair London

  • Highly Experienced Personnels – When it comes quality, we have the best of it all. Our engineers are experienced, accredited and fully equipped with the needed tools to carry out any kind of Vaillant repairs. More so, they are very quick with diagnosis and finding the right solution to your Vaillant boilers.
  • Wide Network – What makes a Vaillant boiler repair company stand out is their accessibility when needed. Vaillant boiler repair London has this just in place. We have a wide network that is available 24/7. Our engineers will be right at your doorsteps immediately you reach out to them.
  • Affordable Price – Getting our services doesn’t mean you have to rob a bank. We offer Vaillant boiler repair at affordable prices. Moreover, we usually send our quotes upfront before going ahead with repair to aid transparency. We don’t include additional cost after the job, neither do we have hidden charges.

With all that is been shared above, we are sure you will look no further, as you have found the perfect Vaillant repair company to help with your Vaillant repairs. We just a call away.

Get In Touch

You can contact Master Gas 24 hours a day and a member of our team will only be pleased to receive your call request.
By using Master Gas you can rest assured that your job will be completed by experts and to your satisfaction, not forgetting, of course, our workmanship guarantee. Call today
07948 009 319

 

Boiler Replacement London

Vaillant Boiler Error Codes

Fault CodePossible CauseMeaning
F.00NTC FaultsThis means that your Flow NTC (Negative Temperature Coefficient Thermistor) cable is either defective or broken and needs to be replaced
F.01The Flow NTC (Negative Temperature Coefficient Thermistor) cable is either defective or broken and needs to be replaced
F.10
F.11
F.13
F.20Boiler has exceeded the maximum temperature and needs to cool down
F.22Dry fire / Low water in system / OverheatThis means that there’s either no water in your system, you have a defective pump or the pump lead is defective
F.24Low water / Pump Failure / BlockagePump could be obstructed, running at low capacity, could be air trapped or the pressure might be too low.
F.28Either insufficient gas in the system, a defective electrode, ignition lead or electronic ignitor
F.29Flame extinguishedFlame or pilot light has gone out – check flue duct or gas supply.
F.60Gas valve control defectiveCable loom (connects gas valve) might have short circuited, gas valve assembly defective or electronic control system issue.
F.61Gas valve control defectiveCable loom (connects gas valve) might have short circuited, gas valve assembly defective or electronic control system issue.
F.62Defective gas valve closure mechanismBoiler has exceeded the maximum temperature and needs to cool down
F.63EEPROM (Electrically Erasable Programmable Read-Only Memory) errorElectronic fault.
F.64Electronic system or sensor faultFlow or back flow NTC has short circuited, or an electronic fault
F.65Electronic system temperature too highThis can happen because of an external heat source or an electrical fault
F.67Electronic fault in the flame system
Fault CodePossible Cause
F.1Lack of gas, a fault with the ignition or flue – may need to adjust the gas valve or replace a defective electrode lead.
F.4Ignition fault.
F.5The system has suffered a fault due to overheating.
F.6Your flow NTC has developed a fault.
F.17Check the polarity of your system.
F.24Pump-related faults – the pump could have failed, it may have over run or there could be an issue with the airlock
Fault CodePossible Cause
F.00, .04, .05, .10, .14, .15All of these are NTC faults, and are best resolved by first changing all NTC to make diagnosis earlier.
F.21The pilot flame has failed.
F.22There is insufficient water in your system.
F.11A blockage in the appliance is preventing the system from flowing as it should.
F.12A blockage in the appliance is affecting the system’s pressure.
F.13The appliance is blocked because of a water deficiency.
Fault CodePossible Cause
S.OHeating issue, no heat demand
S.1Fan start-up error
S.2Pump flow error
S.3Heating mode error – ignition problem
S.4Heat mode – burner on error
S.6Heating mode – fan overrun error
S.7Heating mode – pump overrun error
S.8Heating remaining cut off for XX amount of time
S.31No heat demand summer operating mode
S.34Heating mode frost protection error
S.20Hot water requirement error
S.22Hot water handling pump flow error
S.24Hot water operation burner is on
S.85Service message quantity of circulation water
Fault CodePossible Cause
F.00 / F.0Flow temperature sensor interruption
F.01 / F.1Return temperature sensor interruption
F.10Flow NTC short circuit
F.11Return NTC short circuit
F.20Safety switch off temperature limiter
F.22Safety switch off low water pressure
F.23Safety switch off temperature difference too great
F.24Safety switch off temperature is rising to fast
F.25Safety switch off flue gas temperature too high
F.26Error with gas valve – possible no function
F.27Safety switch off flame simulation
F.28Failure during start up – ignition unsuccessful to start
F.29Failure during operation – re-ignition unsuccessful
F.32Fan error
F.49eBUS error – possible short circuit
F.61Error with gas valve regulation
F.62Error with gas valve – switch off delay
F.63EEPROM error
F.64Electronics / NTC error
F.65Electronic temperature error could be overheating due to external influences
F.67Electronics flame signal error
F.68Unstable flame signal error air in gas
F.70Invalid device specific number (DSN)
F.71Flow NTC error – flow temperature sensor signal constant value
F.72Flow return NTC error – temperature difference too great
F.73Water pressure sensor signal in the wrong range, it is too low
F.74Water pressure sensor signal outside correct range, the sensor signal is too high
F.75Error with pressure – no pressure change detection when starting the pump
F.76Overheating protection on – primary heat exchanger has responded
F.77Flue non return flap condensate pump error
F.78Interruption to DHW outlet sensor at external controller
F.83Flow and or return temperature sensor error
F.84Error with flow/return temperature sensor temperature changing error
F.85Error with flow and return temperature, sensor incorrectly fitted
CONNECTIONNo communication with the PCB
Fault CodePossible Cause
S.00Heating mode error – no heat demand
S.01Heating mode fan start-up
S.02Heating mode error – water pump running
S.03Heating mode – ignition sequence error
S.04Heating mode – burner ignited
S.06Heating mode – fan overrun error
S.07Heating mode – pump overrun error
S.08Heating remaining cut off time xx minutes
S.10Hot water demand via impeller sensor
S.11DHW mode fan start up error
S13DHW mode ignition error
S.14Hot water demand via fan sensor error
S.15DHW mode pump and fan overrun
S.16DHW mode – fan overrun error
S.17DHW mode – pump overrun error
S.20DHW mode – burner on error
S.21DHW mode – fan start up error
S.22DHW demand – error pump running
S.23DHW ignition error
S.24DHW mode – burner error
S.25DHW mode – pump or fan overrun error
S.26DHW mode – fan overrun
S.27DHW mode – pump overrun
S.28Hot water burner anti-cycling time
S.30Room thermostat is blocking heating mode
S.31No heat demand boiler in summer operating mode
S.32Waiting period because of fan speed deviation
S.34Heating mode frost protection error
S.39Burner off contact has been triggered this could be because of contact thermostat or condensate pump
S.40Comfort safety mode active
S.41Water pressure > 2.8 bar
S.42Flue non return flap return signal blocks burner operation
S.46Comfort safety mode flame loss at minimum load
S.53Boiler is in waiting period of modulation f block function due to water shortage
S.54Boiler is in waiting period of operation, blocking function as a result
S.57Waiting period comfort safety mode
S.58Modulation limitation due to noise / wind error
S.61Gas family check unsuccessful
Fault CodePossible Cause
S.20Warnstar demand
S.21Fan running
S.22Pump running
S.23Ignition sequence
S.24Burner ignited
S.25Fan and water pump running
S.26Fan overrun
S.27Pump overrun
S.28Anti-cycling mode
S.30No heating demand from external controls
S.31Central heating thermostat knob turned off
S.32Heat exchanger antifreeze active as fan speed variation is too high
S.34Anti-frost mode is active
S.36Not heating demand form low voltage
S.41Water pressure greater than 2.9 bar
S.42Response from accessory module or defective condensate pump is blocking burner operation
S.53Appliance is within the waiting period of the block operation function due to water shortage
S.54Appliance is within the waiting period of the block operation due to water shortage
S.96Return sensor error
S.98Flow return sensor check is running demand is block
D.0Heating part load error
D.1Water pump overrun – time for heat mode
D.2Max burner anti-cycling period at 20c flow temperature
D.3Hot water flow temperature reading
D.4Current temperature for warm stat sensor
D.7Warm start temperature target value
D.8External controls heat demand
D.9Flow target temperature from external analogue regulator terminal
D.10Status internal heating pump error
D,11Status external heating pump error
D.12Cylinder charging pump via accessory module
D.13Hot water circulation pump
D.22Hot water demand
D.23Summer/Winter function
D.25Hot water activation via ebus control
D.30Control signal for both gas valves
D.33Fan speed target value
D.34Fan speed actual value
D.36Hot water flow sensor
D.40Flow temperature target value
D.41Return temperature actual value
D.44Digitised ionisation potential error
D.47Outside temperature with weather compensator – Vaillant controller only
D.76Remaining burner anti-cycling time in min
D.90Digital regulator status
D.91DCF status with connected external probe
D.97Activation of the second diagnostic level
D.17Heating glow return regulation
D.18Pump mode return
D.19Operating modes of the two speed heating pump
D.20Maximum set value for target cylinder
D.27Switching accessory relay 1
D.28Switching accessory relay 2
D.50Offset for minimum speed
D.51Offset for maximum speed
D.58Activation of solar reheating
D.60Number of safety temperature cut off
D.61Number of unsuccessful lockouts
D.64Average ignition times
D.65Maximum ignition time
D.68Unsuccessful ignitions in the first attempt
D.69Unsuccessful ignition for the second time
D.70Set diverter valve position
D.71Maximum setting of heater control knob
D.72Pump overrun time after warm start
D.73Off set for warm start target value
D.75Maximum charging time for a storage without own controller
D.77Limitation of cylinder charging in output in kW
D.78Limitation of cylinder charging temperature in c
D.80Operating hours heating
D.81Operating hours hot water generation
D.82Burner start up in heating mode
D.83Burner start up in hot water mode
D.84Maintenance indicator – number of hours until the next maintenance
D.93DSN appliance variant setting
D.96Factory setting
Fault CodePossible Cause
P.00The heating circuit and hot water circuit are purged
P.01Maximum load test program error
P.02Minimum load test program
P.06Filling mode test program
Fault CodePossible Cause
D.0Heating part load error
D.1Water pump overrun – time for heat mode
D.2Max burner anti-cycling period at 20c flow temperature
D.3Hot water flow temperature reading
D.4Current temperature for warm stat sensor
D.5Set value of flow temperature or target value of return
D.7Warm start temperature target value
D.8External controls heat demand
D.9Flow target temperature from external analogue regulator terminal
D.10Status internal heating pump error
D,11Status external heating pump error
D.12Cylinder charging pump via accessory module
D.13Hot water circulation pump
D.15Pump speed actual value
D.22Hot water demand
D.23Summer/Winter function
D.24Not relevant
D.25Hot water activation via eBus control
D.30Control signal for both gas valves
D.33Fan speed target value
D.34Fan speed actual value
D.35Not relevant
D.40Flow temperature target value
D.41Return temperature actual value
D.44Digitised ionisation – potential error
D.47Outside temperature with weather compensator – Vaillant controller only
D.76Remaining burner anti-cycling time in min
D.90Digital regulator status
D.91DCF status with connected external probe
D.97Activation of the second diagnostic level
D.98Telephone a heating engineer
D.14Pump speed target value
D.17Heating flow return regulation
D.18Pump operating mode
D.20Maximum set value for target cylinder
D.26Additional relay control ecoTec
D.27Switching accessory relay 1
D.28Switching accessory relay 2
D.50Offset for minimum speed
D.51Offset for maximum speed
D.60Number of safety temperature cut offs
D.61Number of unsuccessful lockouts
D.64Average ignition times
D.65Maximum ignition time
D.67Remaining burner anti-cycling time
D.68Unsuccessful ignitions in the first attempt
D.69Unsuccessful ignition for the second time
D.70Set diverter valve position
D.71Maximum setting of heater control knob
D.72Pump overrun time after warm start
D.75Maximum charging time for a storage without own controller
D.77Limitation of cylinder charging in output in kW
D.78Limitation of cylinder charging temperature in celsius
D.80Operating hours heating
D.81Operating hours hot water generation
D.82Burner start up in heating mode
D.83Burner start up in hot water mode
D.84Maintenance indicator – number of hours until the next maintenance
D.93DSN appliance variant setting
D.96Factory setting
Vaillant Boiler Repairs London
Boiler Repair, Vaillant

Boiler Replacement London

Boiler Replacement London

Do you need a gas boiler replacement and you don’t know how to go about it? Perhaps, you want a company that can help you with the replacement at an affordable cost? We can help you with the replacement of our gas boiler within a very timely manner.

When it comes to carrying out a gas boiler replacement in your home, you can’t afford to let an unprofessional do this for you. Just a single mistake could cause more damage and cost you a lot more than you were trying to save in the first place. We are sure you don’t want such and thought of not making such mistake has brought you here.

Expert Gas Boiler Replacements London

As professionals that deals with Gas boiler replacements, we know exactly what you need and how you want it done. Our experiences with our countless previous clients give us insight as to the way and manner you want this replacement to be done. Our engineers are registered gas engineers with full qualifications on installations and repairs. Unlike others, we are not restricted to just a single boiler brand. We have the full accreditation to install Worcester Bosch boiler, Viessmann, and Vaillant boilers. Despite, we are completely independent. Which means you will be getting the best advice from us as to which brand to go for to cater for your gas boiler replacement needs.

In addition to helping with your gas boiler replacement, we will take a step further by helping you to register the replacement of the gas boiler with Gas Safe Register. You will be issued a certificate for this and this will serve as your insurance.

Thinking of how long it might take us to finish with your gas boiler replacement? We are very time-sensitive, but this usually takes about 2-3 days to finish up. However, this time is directly related to the present state of your central heating system and also the type and brand of the boiler to be installed.

Moreover, hiring us to help with your gas boiler replacement will give you the exclusive opportunity to get advice from or professionals on how to maintain your newly replaced gas boiler.

WHY CHOOSE US?

  • You will be entitled to excellent customer care that is ready to satisfy you always
  • A competitive price that will suit your budget.
  • Guaranteed insurance that protects you

No form of hidden charges or after work cost.

Get In Touch

You can contact Master Gas 24 hours a day and a member of our team will only be pleased to receive your call request.
By using Master Gas you can rest assured that your job will be completed by experts and to your satisfaction, not forgetting, of course, our workmanship guarantee. Call today
07948 009 319

 

Boiler Replacement London

Vaillant Boiler Error Codes

Fault CodePossible CauseMeaning
F.00NTC FaultsThis means that your Flow NTC (Negative Temperature Coefficient Thermistor) cable is either defective or broken and needs to be replaced
F.01The Flow NTC (Negative Temperature Coefficient Thermistor) cable is either defective or broken and needs to be replaced
F.10
F.11
F.13
F.20Boiler has exceeded the maximum temperature and needs to cool down
F.22Dry fire / Low water in system / OverheatThis means that there’s either no water in your system, you have a defective pump or the pump lead is defective
F.24Low water / Pump Failure / BlockagePump could be obstructed, running at low capacity, could be air trapped or the pressure might be too low.
F.28Either insufficient gas in the system, a defective electrode, ignition lead or electronic ignitor
F.29Flame extinguishedFlame or pilot light has gone out – check flue duct or gas supply.
F.60Gas valve control defectiveCable loom (connects gas valve) might have short circuited, gas valve assembly defective or electronic control system issue.
F.61Gas valve control defectiveCable loom (connects gas valve) might have short circuited, gas valve assembly defective or electronic control system issue.
F.62Defective gas valve closure mechanismBoiler has exceeded the maximum temperature and needs to cool down
F.63EEPROM (Electrically Erasable Programmable Read-Only Memory) errorElectronic fault.
F.64Electronic system or sensor faultFlow or back flow NTC has short circuited, or an electronic fault
F.65Electronic system temperature too highThis can happen because of an external heat source or an electrical fault
F.67Electronic fault in the flame system
Fault CodePossible Cause
F.1Lack of gas, a fault with the ignition or flue – may need to adjust the gas valve or replace a defective electrode lead.
F.4Ignition fault.
F.5The system has suffered a fault due to overheating.
F.6Your flow NTC has developed a fault.
F.17Check the polarity of your system.
F.24Pump-related faults – the pump could have failed, it may have over run or there could be an issue with the airlock
Fault CodePossible Cause
F.00, .04, .05, .10, .14, .15All of these are NTC faults, and are best resolved by first changing all NTC to make diagnosis earlier.
F.21The pilot flame has failed.
F.22There is insufficient water in your system.
F.11A blockage in the appliance is preventing the system from flowing as it should.
F.12A blockage in the appliance is affecting the system’s pressure.
F.13The appliance is blocked because of a water deficiency.
Fault CodePossible Cause
S.OHeating issue, no heat demand
S.1Fan start-up error
S.2Pump flow error
S.3Heating mode error – ignition problem
S.4Heat mode – burner on error
S.6Heating mode – fan overrun error
S.7Heating mode – pump overrun error
S.8Heating remaining cut off for XX amount of time
S.31No heat demand summer operating mode
S.34Heating mode frost protection error
S.20Hot water requirement error
S.22Hot water handling pump flow error
S.24Hot water operation burner is on
S.85Service message quantity of circulation water
Fault CodePossible Cause
F.00 / F.0Flow temperature sensor interruption
F.01 / F.1Return temperature sensor interruption
F.10Flow NTC short circuit
F.11Return NTC short circuit
F.20Safety switch off temperature limiter
F.22Safety switch off low water pressure
F.23Safety switch off temperature difference too great
F.24Safety switch off temperature is rising to fast
F.25Safety switch off flue gas temperature too high
F.26Error with gas valve – possible no function
F.27Safety switch off flame simulation
F.28Failure during start up – ignition unsuccessful to start
F.29Failure during operation – re-ignition unsuccessful
F.32Fan error
F.49eBUS error – possible short circuit
F.61Error with gas valve regulation
F.62Error with gas valve – switch off delay
F.63EEPROM error
F.64Electronics / NTC error
F.65Electronic temperature error could be overheating due to external influences
F.67Electronics flame signal error
F.68Unstable flame signal error air in gas
F.70Invalid device specific number (DSN)
F.71Flow NTC error – flow temperature sensor signal constant value
F.72Flow return NTC error – temperature difference too great
F.73Water pressure sensor signal in the wrong range, it is too low
F.74Water pressure sensor signal outside correct range, the sensor signal is too high
F.75Error with pressure – no pressure change detection when starting the pump
F.76Overheating protection on – primary heat exchanger has responded
F.77Flue non return flap condensate pump error
F.78Interruption to DHW outlet sensor at external controller
F.83Flow and or return temperature sensor error
F.84Error with flow/return temperature sensor temperature changing error
F.85Error with flow and return temperature, sensor incorrectly fitted
CONNECTIONNo communication with the PCB
Fault CodePossible Cause
S.00Heating mode error – no heat demand
S.01Heating mode fan start-up
S.02Heating mode error – water pump running
S.03Heating mode – ignition sequence error
S.04Heating mode – burner ignited
S.06Heating mode – fan overrun error
S.07Heating mode – pump overrun error
S.08Heating remaining cut off time xx minutes
S.10Hot water demand via impeller sensor
S.11DHW mode fan start up error
S13DHW mode ignition error
S.14Hot water demand via fan sensor error
S.15DHW mode pump and fan overrun
S.16DHW mode – fan overrun error
S.17DHW mode – pump overrun error
S.20DHW mode – burner on error
S.21DHW mode – fan start up error
S.22DHW demand – error pump running
S.23DHW ignition error
S.24DHW mode – burner error
S.25DHW mode – pump or fan overrun error
S.26DHW mode – fan overrun
S.27DHW mode – pump overrun
S.28Hot water burner anti-cycling time
S.30Room thermostat is blocking heating mode
S.31No heat demand boiler in summer operating mode
S.32Waiting period because of fan speed deviation
S.34Heating mode frost protection error
S.39Burner off contact has been triggered this could be because of contact thermostat or condensate pump
S.40Comfort safety mode active
S.41Water pressure > 2.8 bar
S.42Flue non return flap return signal blocks burner operation
S.46Comfort safety mode flame loss at minimum load
S.53Boiler is in waiting period of modulation f block function due to water shortage
S.54Boiler is in waiting period of operation, blocking function as a result
S.57Waiting period comfort safety mode
S.58Modulation limitation due to noise / wind error
S.61Gas family check unsuccessful
Fault CodePossible Cause
S.20Warnstar demand
S.21Fan running
S.22Pump running
S.23Ignition sequence
S.24Burner ignited
S.25Fan and water pump running
S.26Fan overrun
S.27Pump overrun
S.28Anti-cycling mode
S.30No heating demand from external controls
S.31Central heating thermostat knob turned off
S.32Heat exchanger antifreeze active as fan speed variation is too high
S.34Anti-frost mode is active
S.36Not heating demand form low voltage
S.41Water pressure greater than 2.9 bar
S.42Response from accessory module or defective condensate pump is blocking burner operation
S.53Appliance is within the waiting period of the block operation function due to water shortage
S.54Appliance is within the waiting period of the block operation due to water shortage
S.96Return sensor error
S.98Flow return sensor check is running demand is block
D.0Heating part load error
D.1Water pump overrun – time for heat mode
D.2Max burner anti-cycling period at 20c flow temperature
D.3Hot water flow temperature reading
D.4Current temperature for warm stat sensor
D.7Warm start temperature target value
D.8External controls heat demand
D.9Flow target temperature from external analogue regulator terminal
D.10Status internal heating pump error
D,11Status external heating pump error
D.12Cylinder charging pump via accessory module
D.13Hot water circulation pump
D.22Hot water demand
D.23Summer/Winter function
D.25Hot water activation via ebus control
D.30Control signal for both gas valves
D.33Fan speed target value
D.34Fan speed actual value
D.36Hot water flow sensor
D.40Flow temperature target value
D.41Return temperature actual value
D.44Digitised ionisation potential error
D.47Outside temperature with weather compensator – Vaillant controller only
D.76Remaining burner anti-cycling time in min
D.90Digital regulator status
D.91DCF status with connected external probe
D.97Activation of the second diagnostic level
D.17Heating glow return regulation
D.18Pump mode return
D.19Operating modes of the two speed heating pump
D.20Maximum set value for target cylinder
D.27Switching accessory relay 1
D.28Switching accessory relay 2
D.50Offset for minimum speed
D.51Offset for maximum speed
D.58Activation of solar reheating
D.60Number of safety temperature cut off
D.61Number of unsuccessful lockouts
D.64Average ignition times
D.65Maximum ignition time
D.68Unsuccessful ignitions in the first attempt
D.69Unsuccessful ignition for the second time
D.70Set diverter valve position
D.71Maximum setting of heater control knob
D.72Pump overrun time after warm start
D.73Off set for warm start target value
D.75Maximum charging time for a storage without own controller
D.77Limitation of cylinder charging in output in kW
D.78Limitation of cylinder charging temperature in c
D.80Operating hours heating
D.81Operating hours hot water generation
D.82Burner start up in heating mode
D.83Burner start up in hot water mode
D.84Maintenance indicator – number of hours until the next maintenance
D.93DSN appliance variant setting
D.96Factory setting
Fault CodePossible Cause
P.00The heating circuit and hot water circuit are purged
P.01Maximum load test program error
P.02Minimum load test program
P.06Filling mode test program
Fault CodePossible Cause
D.0Heating part load error
D.1Water pump overrun – time for heat mode
D.2Max burner anti-cycling period at 20c flow temperature
D.3Hot water flow temperature reading
D.4Current temperature for warm stat sensor
D.5Set value of flow temperature or target value of return
D.7Warm start temperature target value
D.8External controls heat demand
D.9Flow target temperature from external analogue regulator terminal
D.10Status internal heating pump error
D,11Status external heating pump error
D.12Cylinder charging pump via accessory module
D.13Hot water circulation pump
D.15Pump speed actual value
D.22Hot water demand
D.23Summer/Winter function
D.24Not relevant
D.25Hot water activation via eBus control
D.30Control signal for both gas valves
D.33Fan speed target value
D.34Fan speed actual value
D.35Not relevant
D.40Flow temperature target value
D.41Return temperature actual value
D.44Digitised ionisation – potential error
D.47Outside temperature with weather compensator – Vaillant controller only
D.76Remaining burner anti-cycling time in min
D.90Digital regulator status
D.91DCF status with connected external probe
D.97Activation of the second diagnostic level
D.98Telephone a heating engineer
D.14Pump speed target value
D.17Heating flow return regulation
D.18Pump operating mode
D.20Maximum set value for target cylinder
D.26Additional relay control ecoTec
D.27Switching accessory relay 1
D.28Switching accessory relay 2
D.50Offset for minimum speed
D.51Offset for maximum speed
D.60Number of safety temperature cut offs
D.61Number of unsuccessful lockouts
D.64Average ignition times
D.65Maximum ignition time
D.67Remaining burner anti-cycling time
D.68Unsuccessful ignitions in the first attempt
D.69Unsuccessful ignition for the second time
D.70Set diverter valve position
D.71Maximum setting of heater control knob
D.72Pump overrun time after warm start
D.75Maximum charging time for a storage without own controller
D.77Limitation of cylinder charging in output in kW
D.78Limitation of cylinder charging temperature in celsius
D.80Operating hours heating
D.81Operating hours hot water generation
D.82Burner start up in heating mode
D.83Burner start up in hot water mode
D.84Maintenance indicator – number of hours until the next maintenance
D.93DSN appliance variant setting
D.96Factory setting
Worcester Bosch Boiler Repairs(1)
Boiler Repair, Worcester

Worcester Bosch Boiler Repair

Worcester Bosch Boiler Repair

Worcester Bosch Boiler specialist

Is your boiler damaged and in need of a repair? Why leave it that way when can get a Worcester Bosch boiler repair to fix it for you. Perhaps you just can’t cope with the high budget and time needed to get this done? We as a Worcester Bosch boiler repair agent, we understand your plights as well as your needs as an individual when it comes to repairing your boiler. That’s why we are offering this service at an unbeatable price, with enough flexibility to fit into your schedule.

We are not restricted to a particular type of model or make of boiler. Our experts have the required knowledge cut across several models and makes of boiler. Which means we can work on any Worcester bosh boiler you have installed in your home. Having the experience and knowledge in place, you need to look no further. As we are just a dial away from you.

Worcester Bosch boiler repair company

As a Worcester Bosch boiler repair company, we have the best in place. Here, our engineers are professionals groomed with the required training when it comes to handling natural gas. More so,  they are Gas Safe registered. Which means you can count on them with the handling of your highly sensitive boiler. We also have an insurance policy in place that protects you. With this, the safety of you and your home is guaranteed.

Even though natural gas is highly beneficial, they tend to cause havoc if not properly handled. With your boiler been damaged, you stand a great risk and this could cause severe damages to your home and environs if not the fixed right away. We have engineers that know how to repair a boiler without any gas leak. With our Worcester Bosch boiler repair, you can rest assured that you are safe because you have the best overseeing the repair of your boiler.

Moreover, winter is just around the corner looming. And of course, you need not be reminded of how cold winter can be here in London. Why go through this season without a properly functioning boiler when you can hire our Worcester Bosch boiler repair services and get it fixed.

Conclusion

Provided you reside here in the beautiful city of London, our services would reach you in a very timely manner. We are available 24/7, ready to give you the best when it comes to Worcester Bosch boiler repairs.

Get In Touch

You can contact Master Gas 24 hours a day and a member of our team will only be pleased to receive your call request.
By using Master Gas you can rest assured that your job will be completed by experts and to your satisfaction, not forgetting, of course, our workmanship guarantee. Call today
07948 009 319

 

Boiler Replacement London

Worcester Boiler Error Codes

Fault DescriptionSystem Behaviour
226Service tool has been connected in the blocking error history menu
FD 231The power has been interrupted during a lockout
C7 214Fan does not run during the start up phase – fan harness connector needs checking
C6 215Fan speed too high – check the fan harness and connector
C7 216Fan speed too low – check the fan harness and connector
C7 217Fan has stopped during appliance operation
C1 264Fan stopped during operation
C4 273Continuous fan operation for the last 24 hours – appliance temporarily blocked
E2 222Flow temperature sensor shorted
E2 233Flow temperature sensor disconnected
E9 276Primary flow temperature exceeded 95°c
E2 350Flow temperature sensor shorted
E2 351Flow temperature sensor disconnected
FA 306Ionisation detected after the gas valve closed
EA 227No ionisation detected after ignition
F7 228Isioniation current detected before burner start
EA 229Loss of ionisation signal during operation
EA 261Heat control module (HCM) potentially defective – reset the appliance
9U 233Control box or heat control module (HCM) is defective or loose, the HCM needs to be checked
C4 237Control box or heat control module (HCM) is defective
F0 238Gas valve or control box error – gas valve coils need checking
F0 239Control box or the heat control module (HCM) is defective – the control box connections need checking
F0 242Control box or the heat control module (HCM) is defective – the HCM and control box connections need to be checked
B7 257Control box or the heat control module HCM) is defective- the HCM and control box connections need to be checked
F0 258Control box or the heat control module (HCM) is defective – HCM or control box connections need to be checked
EH 258Control box or the heat control module (HCM) is defective – HCM or control box connections need to be checked
F1 259Control box or the heat control module (HCM) is defective – HCM or control box connections need to be checked
F0 262Control box or the heat control module (HCM) is defective – HCM or control box connections need to be checked
F1 263Control box or the heat control module (HCM) is defective – HCM or control box connections need to be checked
F0 272Control box or the heat control module (HCM) is defective – control box and connections need checking or HCM might not be inserted properly and need replacing
F0 280Control box or the heat control module (HCM) is defective – control box and connections need checking or HCM might not be inserted properly and need replacing
F0 290Control box is defective – HCM needs checking as it might not be inserted properly or need replacing
328Internal error with the mains voltage – frequency may be inconsistent
235Incompatible heat control module (HCM) software versions – control box needs latest software
356Low mains voltage – the voltage may be interrupted or inconsistent and needs checking
360Heat control module (HCM) invalid – the inserted HCM does not correspond with the control box
A8 362Low mains voltage – the voltage may be interrupted, inconsistent or heat control module (HCM) invalid
CC 800Outdoor sensor defect available when accessory outdoor sensor is connected
A1 281Pump stock or running dry
E9 224Flue or high limit thermostat activated
D4 341Primary flow temperature rising too fast
Fault DescriptionSystem Behaviour
208The boiler is in chimney sweep mode
200The boiler is in heating mode
201The boiler is in domestic hot water (DHW) mode
202The boiler is waiting – there was a heat demand from the on off or modulating control
203The boiler is on standby
204The boiler is waiting – the actual temperature is higher than the calculated or selected boiler temperature
212The temperature recorded by the flow temperature sensor or the safety sensor is rising too quickly
226Diagnosis tool was connected and is now locked out
260The flow temperature sensor is not detecting a rise in temperature following a burner start
265The boiler is waiting in response to a heat demand – the boiler regularly switches to partial load
268Component test phase
270The boiler is modulating upwards
283The boiler is preparing for a burner start – the fan and pump are activated
284The gas valve is switched
305The boiler is waiting for domestic hot water (DHW) operation to end
235The KIM (boiler identification module) is too new for the burner control unit
360The KIM that has been fitted is not compatible with the burner control unit
9A 361The burner control unit that has been fitted is not compatible with the KIM (boiler identification module)
9U 233The burner control unit or KIM (boiler identification module) is faulty
A3 317Short circuit in the flue gas temperature sensor contacts
B7 257The burner control unit or the KIM (boiler identification module) is faulty
C1 264No control signal or power supply to the fan during operation
C4 273The boiler was switched off for a maximum of 2 minutes because it had been operating continuously for more than 24 hours
C6 215The fan speed is too high
C6 216The fan speed is too low
C7 214The fan does not run during the start phase
C7 217The fan speed is irregular when starting up
CE 207Water pressure is too low
CE 266Pump test failed
D1 240The contacts of the boiler return temperature sensor have been short circuited
D1 241The contacts of the boiler return temperature sensor have been interrupted
D3 232The external switching contact has opened
D4 213The actual temperature recorded by the flow temperature sensor or return temperature sensor is rising too quickly
D4 271Actual temperature differential between flow and safety temperature sensor is too high
D4 286The boiler return temperature sensor has detected a return temperature higher than 105°c
E2 222Short circuit in the flow temperature sensor contacts
E2 223The flow temperature sensor contacts have been interrupted
E5 218The temperature captured by the flow temperature sensor exceeded 105°c
E9 210The temperature measured by the flue gas sensor is too high and is open
E9 219The safety temperature sensor has captured a temperature in excess of 105°C
E9 220The contacts for the safety temperature sensor have shorted or the safety temperature sensor has detected a temperature higher than 130°c
E9 224The contacts of the safety temperature sensor have been interrupted
E9 276The temperature flow sensor has measured a temperature in excess of 95°c
E9 277The safety temperature sensor has measured temperature in excess of 95°c
E9 285The boiler return temperature sensor has measured a temperature higher than 95°c
E9 318The flue gas temperature sensor contacts have been interrupted
EA 227An insufficient ionisation current was measured following ignition of the burner
EA 229The ionisation current detected by the system during the burning phase was insufficient
EA 234The contacts of the gas valve have been interrupted
EA 261The burner control unit is faulty
EA 269The ignition device has been activated for too long
F0 238The burner control unit KIM (boiler identification module) is faulty
F0 239The burner control unit KIM (boiler identification module) has an error. Cabling might have poor contact breaks and pinching or the plug and wiring of the burner control unit needs checking, also check the operating characteristics of the boiler by replacing the burner control unit.
F0 242, F0 243. F0 244. F0 245, F0 246. F0 247, F0 248, F0 249, F0 250, F0 251, F0 252, F0 253, F0 255, F0 259, F0 263, F0 267, F0 272The burner control unit (KIM) is faulty – the wiring of the burner control unit needs checking, also check the operating characteristics of the boiler by replacing the burner control unit.
F0 278The sensor test has failed – cabling and plug sensors need checking
F0 279The burner control unit, or KIM, is faulty – control unit may need replacing
F0 280The burner control unit is faulty
F0 287The burner control unit, or KIM, has an error
F0 290The burner control unit, or KIM, is faulty
F7 228An ionisation current was measured before the burner started
F7 328A brief power failure has occurred
FA 306An ionisation current was measured after the burner went out
FD 231The mains voltage was interrupted during an interlocking fault
EC 256The burner control unit has an error
EH 258The burner control unit is faulty – check the plug and wiring of the burner control unit.
H07The current water pressure is too low, limiting the performance in heat mode as well as domestic hot water (DHW) mode
HrEThe boiler keeps resetting
rEThe boiler resets
Fault DescriptionSystem Behaviour
Light offNo boiler demand
Light onHeating demand on boiler is OK
1 flash 5 seconds offNo ionisation detected after ignition
2 flashes 5 seconds offLoss of ionisation signal during operation
3 flashes 5 seconds offGas valve error
4 flashes 5 seconds offFirst safety timing error / ignition timing error
5 flashes 5 seconds offIonisation detected after burner stopped
Gas valve EV2 leak test failed
Gas valve EV1 leak test failed
Ionisation current detected before burner start
Gas valve error
Ionisation sensor shorted
4 flashes 5 second gap 1 long flashSensor test failed
4 flashes, 5 second gap, 2 long flashesSafety temperature too high
4 flashes, 5 second gap, 3 long flashesMax safety thermostat activated
4 flashes, 5 second gap, 4 long flashesReturn temperature too high
4 flashes, 5 second gap, 5 long flashesFlow temperature too high – supply sensor exceeded 110°c
1 long flash, 4 quick flashes, 5 second gap, 1 long flash, 4 quick flashesHeating control module (HCM) defective
2 long flashes, 4 quick flashes, 5 second gap, 2 long flashes, 4 quick flashesFan running too fast
Fan running too slow
No airflow after defined period of time
Fan not running
3 long flashes, 4 quick flashes, 5 second gap, 3 long flashes, 4 quick flashesMains voltage interrupted after locking error
4 long flashes, 4 quick flashes, 5 second gap, 4 long flash, 4 quick flashesInternal control board faults
5 long flashes, 4 quick flashes, 5 second gap, 5 long flash, 4 quick flashesAll other miscellaneous faults – reset the boiler by turning the control knob anti-clockwise to the reset position
Fault DescriptionSystem Behaviour
No lightNo power at control board
Light onAppliance on but not operating during demand
Slow flash ( mostly off flashes on)Ignition lockout
Slow flash ( mostly on flashes off)Flue overheat or heat exchanger overheat
Fast flashVolatile lockout sensor fan or code plug
2 pulsesCheck service mode switch is in minimum position
5 pulsesCheck service mode switch is in max position
Fault DescriptionSystem Behaviour
200 OBoiler in heating mode
201 OBoiler in hot water mode
202 OBoiler in anti-cycle mode
203 0Boiler in standby – no heat energy demand
204 OCurrent primary water temperature higher than set value
208 0Chimney sweep demand
224 VSafety temperature limiter has tripped – top-up water until the reset pressure is reached
227 VNo flame signal after ignition burner control unit could need replacing
228 VFlame signal without flame present – air/gas ratio control valve may need replacing as might the ionisation cable
305 0Boiler in hot water anti-cycle mode
306 VFlame signal after closing the fuel supply – the air/gas ratio control valve might need replacing
360 VIncompatible code plug – check if a correct code plug is installed and exchange or reconnect code plug
815 W/BLow loss header temperature sensor faulty – check the sensor port or check the differential sensor for incorrect installation position or breakage
1010 ONo BUS communication cable, EMS-Bus isn’t connected or damaged – connect the cable for the EMS-Bus or replace the damaged cable exchange fuse
1017 WWater pressure too low – the water needs topping up and the vent system or pressure sensor may need replacing
1021 BHot water temperature sensor is defective – the plug to the hot water temperature sensor may not be connected
1022 BHot water storage temperature sensor is defective – connect the plug to the hot water temperature sensor correctly, mount the hot water temperature sensor correctly or replace the hot water temperature sensor
1037 WOutside temperature sensor is defective – check the connecting lead
1065 BPressure sensor defective or not connected – check pressure sensor connection as it may need replacing
1068 WOutside temperature sensor defective – check the connecting lead
1073 WShort circuit of the flow temperature sensor – the temperature sensor may need replacing
1074 WNo signal from the flow temperature sensor available – connect the plug to the flow temperature sensor correctly or temperature sensor could need replacing
1075 WShort circuit of the temperature sensor at the heating block – temperature sensor may need replacing
1076 WNo signal from the temperature sensor at the heating block available – replace the temperature sensor, the connecting lead or the control unit
2920 VError with the flame monitoring
2924 VNo feedback from the modulating gas valve. The gas valve relay is defective – press the reset button and apply burner start, wait to see if fault reoccurs, if it does the gas valve needs replacing
2925 VFeedback from the modulating gas valve is too low
2927 BFlame failed during burner operation. Open the main shut off valve, shut down the appliance and check gas line, replace the ionisation electrode, set burner correctly and minimum rated load, check the integrity flue system and if the interconnected room air supply is too small, or the size of the ventilation opening is too small, clean the heating block on the flue gas side or replace the control unit/burner control unit
2946 VIncorrect code plug detected – the code plug needs replacing
2948 BNo flame signal. With low output the burner starts automatically after cleaning. If the fault occurs repeatedly, the setting of the CO2 valves need checking
2950 BNo flame signal. Following starting procedure the burner starts automatically. After cleaning set the correct gas / air ratio correctly
2963 BSignal from flow and heat exchanger temperature sensor outside the permissible range – the connecting lead needs connecting correctly
2964 BFlow rate in heat exchanger is too low
2965 BFlow temperature too high
2966 BFlow temperature rise in heat exchanger too rapid
2967 BFlow / heat exchanger temperature sensor differential too great
2970 BPressure drop in heating system too rapid
2971 BSystem pressure too low – the heating system needs venting or water needs topping up until the preset pressure is reached. Replace the cable to the pressure sensor replace the pressure sensor
Call Now Button